7643A REV A Norge Dryer Parts List

Lower front dishrack wheel (roller asm lwr rack frnt)

This wheel is located on the front lower rack. It includes the axle. Sold individually.

Dryer drum support roller (Whirlpool dryer drum roller)

The drum support roller has a metallic bearing in its center. This part is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. If your dryer is noisy, will not tumble or takes too long to dry, you might need to replace the roller. It is recommended that you replace both rollers at once. This is a genuine OEM part and is sold individually. Please remember to shut off the power to the dryer before starting the repair.

Flat style oven igniter kit (sub 12400035)

The flat style gas oven igniter is used to ignite the gas to light the oven burner, which produces heat for your range. If the element has shorted out, is no longer glowing, or is glowing but only orange or red rather than white, then you will need to replace the oven igniter. When replacing the igniter please be very careful not to touch the gray element part of the igniter as it is very fragile. The igniter measures approximately 3-3/4"in length and the amperage range is 3.3 to 3.6. This igniter kit can replace igniters for either the broil or bake burners and can replace shorter and longer igniters. The kit includes the igniter, 4 wire nuts, insulation, 2 wire assembly and a bracket. This is a genuine OEM part. Please make sure to disconnect the power and shut off the gas supply before starting your repair.

Drum support roller (drum support roller - for square ported models)

This single drum support roller is used for square-ported model clothes dryers. It has a metallic bearing in its center. This support roller is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. If your dryer is noisy, will not tumble, or takes too long to dry, you might need to replace the roller. It is recommended that you replace both rollers at once. It is sold individually.

Drawer slide rail - right side (refrigerator crisper drawer slide (rail) assembly for right hand side.)

This replacement drawer slide rail is for the right-hand side of your refrigerator. This part attaches to the inside wall of your refrigerator to support the sliding crisper drawer. If the rail is broken or the drawer is not sliding properly, you will need to replace the slide rail. You will need a Phillips screwdriver to complete this repair.

Door strike (striker)

This is a door strike for your washing machine. It is the piece that activates the door switch once the door is closed. If your washer will not start, will not fill with water, or the door will not open/close you may need to replace the door strike. This part is white in color, made from plastic, and measures approximately 2 1/2 inches. This is a genuine OEM part.

Terminal block kit (use 5303935058)

This surface burner terminal block kit comes with interchangeable mounting brackets, ceramic wire nuts, heat shrink protective tubing and wires. This part is used to connect the wire harness to the surface burner element. If your element will not heat at all, or is not heating properly, it is likely an issue with the terminal block and will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power supply before starting your repair.

Refrigerator crisper drawer (pan, crisper (includes illus.)

The crisper drawer with humidity control allows you to adjust the humidity within the crisper. By adjusting the humidity, it will extend the life of your produce. The crisper drawer is made of clear plastic, measures 13 1/2” wide and 18 1/2” deep. The drawer does not include the white trim on the front. This is a genuine OEM part and is sold individually.

Ice maker (icemaker asm)

This ice maker assembly is used to make ice in your refrigerator. The ice maker receives water from the water inlet valve and will freeze until ice cubes are formed. Once the water has been frozen the cubes will be ejected from the mold into the ice bucket. The ice maker will continue the process until the ice bucket has reached the limit. If your ice maker is not making ice you may need to replace this part. This kit includes the fill cup, 4-pin wire harness adapter, and a tube. Disconnect the power and water supply before starting your repair. This ice maker is a genuine OEM part.

Refrigerator center crisper drawer slide rail - white (capacitor-compressor)

This is the center support rail for the crisper drawers. The rail attaches to the shelf frame between the two crisper drawers to provide support for the drawers as they slide in and out. The support rail is white in color and made of plastic. It measures approximately 13.5-inches in length and is a genuine OEM part.

Refrigerator slide-out shelf with glass (refrigerator spill-safe shelf)

Multi rib belt (multi rib belt - 93-3/8")

This dryer drum belt has five ridges, 93-3/8 inches in length, and 3/8 of an inch wide. It is flat, black in color, and is made entirely of rubber. The belt helps rotate the drum. If the drum does not rotate and you can still hear the motor running, the belt may have broken and will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Water inlet valve (filter valve asm)

This genuine replacement water inlet valve with tubing supplies water to the ice maker and water dispenser. The valve is 120 volts and 50/60 Hz. If your ice maker is not making ice or no water is coming from the dispenser, you may need to replace this part. The manufacturer has updated the water inlet valve and it no longer includes the removable pre-filter bracket. If you are unable to reuse the old removable pre-filter bracket, order part number WPW10445062. Please remember to disconnect the water and power supply before starting your repair.

Refrigerator crisper pan (crisper pan)

Dryer high limit thermostat (thermostat, high limit 221 f ()

The three-terminal high-limit thermostat with a terminal extension arm acts as a safety mechanism that keeps the dryer from overheating. When the dryer temperature reaches 221 degrees Fahrenheit, the thermostat will shut off power to the heating element until it drops by 80 degrees Fahrenheit. If your dryer has no heat, takes too long to dry or the thermostat has shorted out, you will need to replace the thermostat. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.